View BU33UC3WG-TR_8421078.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

datashee t product structure silicon monolithic integrated circuit this product is not designed for pr otection against radioactive rays tsz02201-0rbr0a300110-1-2 1/23 29.jan.2015 rev.005 www.rohm.com ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 14 ? 001 cmos ldo regulator series for portable equipments versatile package full cmos ldo regulator buxxuc3wg series general description buxxuc3wg series is high-performance full cmos regulator with 300-ma output, which is mounted on versatile package ssop5 (2.9 mm ? 2.8 mm ? 1.25 mm). it has excellent noise characteristics and load responsiveness characteristics despite its low circuit current consumption of 50 ? a. it is most appropriate for various applications such as power supplies for logic ic, rf, and camera modules rohms. features ? high accuracy detection ? low current consumption ? compatible with small cera mic capacitor (cin=co=1.0uf) ? with built-in output discharge circuit ? high ripple rejection ? on/off control of output voltage ? with built-in over current protection circuit and thermal shutdown circuit ? package ssop5 is similar to sot-23-5 (jedec) ? low dropout voltage typical application circuit key specifications ? output voltage: 1.0v to 3.3v ? accuracy output voltage: 1.0% (25mv) ? low current consumption: 50 a ? operating temperature range: -40c to +85c applications battery-powered portable equipment, etc. package ssop5: 2.90mm x 2.80mm x 1.25mm figure 1. application circuit y y downloaded from: http:///
tsz02201-0rbr0a300110-1-2 2/23 29.jan.2015 rev.005 buxxuc3wg series datasheet ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com connection diagram ssop5 pin descriptions ssop5 pin no. symbol function 1 vin power supply voltage 2 gnd grounding 3 stby on/off control of output voltage (high: on, low: off) 4 n.c. unconnected terminal 5 vout output voltage ordering information (unit : mm) ssop5 2.9 0.2 0.13 4 + 6 4 1.6 2.8 0.2 1.1 0.05 0.05 0.05 + 0.2 0.1 + 0.05 0.03 0.42 + 0.05 0.04 0.95 5 4 12 3 1.25max. 0.2min. 0.1 lot. no top view vin gnd stby n.c. vout marking downloaded from: http:///
tsz02201-0rbr0a300110-1-2 3/23 29.jan.2015 rev.005 buxxuc3wg series datasheet ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com lineup absolute maximum ratings (ta=25c) parameter symbol limit unit power supply voltage vmax -0.3 +6.0 v power dissipation pd 540(*1) mw maximum junction temperature tjmax +125 operating temperature range topr -40 +85 storage temperature range tstg -55 +125 (*1)pd deleted at 5.4mw/ at temperatures above ta=25 , mounted on 70701.6 mm glass-epoxy pcb. recommended operating range (not to exceed pd) parameter symbol limit unit power supply voltage vin 1.7 5.5 v maximum output current imax 300 ma operating conditions (*2)make sure that the output capacitor value is not kept lower than this specified level across a variety of temperature and d c bias characteristic. parameter symbol min. typ. max. unit condition input capacitor cin 0.47(*2) 1.0 - f ceramic capacitor recommended output capacitor co 0.47(*2) 1.0 - f marking q0 q2 q8 r6 y0 y6 y7 output voltage 1.0v 1.1v 1.8v 2.5v 2.8v 3.2v 3.3v part number bu10 bu11 bu18 bu25 bu28 bu32 bu33 downloaded from: http:///
tsz02201-0rbr0a300110-1-2 4/23 29.jan.2015 rev.005 buxxuc3wg series datasheet ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com electrical characteristics (ta=25 , vin=vout+1.0v (*3), stby=vin, cin=1.0 f, co=1.0 f, unless otherwise noted.) this product is not designed for protection against radioactive rays. (*3) vin=2.5v for vout 1.5v (*4) vin=2.5v to 3.6v for vout 1.5v block diagrams parameter symbol limit unit conditions min. typ. max. overall device output voltage vout vout0.99 vout vout1.01 v iout=10 a,vout 2.5v vout-25mv vout+25mv iout=10 a,vout 2.5v operating current iin - 50 90 a iout=0ma operating current (stby) istby - - 1.0 a stby=0v ripple rejection ratio rr 45 70 - db vrr=-20dbv,frr=1khz,iout=10ma, vin=3.6v dropout voltage vsat - 470 700 mv 1.0v vout 1.2v(iout=300ma) - 350 500 mv 1.2v vout 1.5v(iout=300ma) - 280 380 mv 1.5v vout 1.7v(iout=300ma) - 250 320 mv 1.7v vout 2.1v(iout=300ma) - 220 260 mv 2.1v vout 2.5v(iout=300ma) - 200 220 mv 2.5v vout(iout=300ma) line regulation vdl - 2 20 mv vin=vout+1.0v to 5.5v(*4), iout=10 a load regulation vdlo - 25 45 mv iout=0.01ma to 300ma over-current protection (ocp) limit current ilmax 370 550 - ma vo=vout*0.95 short current ishort 50 150 300 ma vo=0v standby block discharge resistor rdsc 20 50 80 vin=5.5v, stby=0v, vout=2.6v stby pin pull-down current istb 0.1 0.9 8.0 a stby=1.5v stby control voltage on vstbh 1.2 - 5.5 v off vstbl -0.3 - 0.3 v cin ??? 1.0 f (ceramic) co ??? 1.0 f (ceramic) cin vin gnd stby stby vout vout co vref ocp stby discharge tsd vin figure 2. block diagrams downloaded from: http:///
tsz02201-0rbr0a300110-1-2 5/23 29.jan.2015 rev.005 buxxuc3wg series datasheet ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com reference data bu10uc3wg (ta=25oc unless otherwise specified.) figure 3. figure 4. figure 5. figure 6. figure 8. figure 7. [] [] = [] [] = [] [] = [] [] = [] [] = = [] [] = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 6/23 29.jan.2015 rev.005 buxxuc3wg series datasheet ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com reference data bu10uc3wg (ta=25oc unless otherwise specified.) figure 12. figure 11. figure 10. figure 9. y y [] [] figure 13. figure 14. = == = == [] [] = [] [] = [] [] = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 7/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxua3wnvx ` datasheet reference data bu10uc3wg (ta=25oc unless otherwise specified.) figure 16. figure 15. figure 17. figure 20. figure 19. figure 18. = = = = = = = = = = = = == = == downloaded from: http:///
tsz02201-0rbr0a300110-1-2 8/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxua3wnvx ` datasheet reference data bu10uc3wg (ta=25oc unless otherwise specified.) figure 21. figure 22. = = = y y = = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 9/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu11uc3wg (ta=25oc unless otherwise specified.) figure 23. figure 24. figure 25. figure 26. figure28. figure 27. [] [] = = [] [] = = [] [] = [] [] = [] [] = [] [] = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 10/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu11uc3wg (ta=25oc unless otherwise specified.) figure 32. figure 31. figure 30. figure 29. y y [] [] [] [] = [] [] = [] [] = = == figure 33. figure 34. = == downloaded from: http:///
tsz02201-0rbr0a300110-1-2 11/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu11uc3wg (ta=25oc unless otherwise specified.) figure 36. figure 35. figure 37. figure 40. figure 39. figure 38. = == = == = = = = = = = = = = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 12/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu11uc3wg (ta=25oc unless otherwise specified figure 41. figure 42. = = = y y = = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 13/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu18uc3wg (ta=25oc unless otherwise specified.) figure 43. figure 44. figure 45. figure 46. figure 48. figure 47. [] [] = = [] [] = = [] [] = [] [] = [] [] = [] [] = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 14/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu18uc3wg (ta=25oc unless otherwise specified.) [] [] = figure 52. figure 51. figure 50. figure 49. = == = == figure 54. figure53. [] [] = y y [] [] [] [] = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 15/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu18uc3wg (ta=25oc unless otherwise specified.) = == = == figure 56. figure 55. figure 57. = = = = = = = = = = = figure 60. figure 59. figure 58. downloaded from: http:///
tsz02201-0rbr0a300110-1-2 16/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu18uc3wg (ta=25oc unless otherwise specified.) figure 61. = = = y y = = = figure 62. downloaded from: http:///
tsz02201-0rbr0a300110-1-2 17/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu33uc3wg (ta=25oc unless otherwise specified.) figure 63. figure 64. figure 65. figure 66. figure 68. figure 67. [] [] = [] [] = [] [] == [] [] == [] [] = [] [] = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 18/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu33uc3wg (ta=25oc unless otherwise specified.) figure 72. figure 71. figure 70. figure 69. figure 74. figure 73. [] [] = [] [] = [] [] = y y [] [] = == = == downloaded from: http:///
tsz02201-0rbr0a300110-1-2 19/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu33uc3wg (ta=25oc unless otherwise specified.) figure 76. figure 75. figure 77. figure 80. figure 79. figure 78. = == = == = = = = = = = = = = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 20/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet reference data bu33uc3wg (ta=25oc unless otherwise specified.) figure 81. figure 82. = = = y y = = = downloaded from: http:///
tsz02201-0rbr0a300110-1-2 21/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet about power dissipation (pd) as for power dissipation, an approximate estimate of the hea t reduction characteristics and internal power consumption of ic are shown, so please use these for reference. sinc e power dissipation changes substantially depending on the implementation conditions (board size, board thickness, metal wi ring rate, number of layers and through holes, etc.), it is recommended to measure pd on a set board. exceeding the po wer dissipation of ic may lead to deterioration of the original ic performance, such as causin g operation of the thermal shutdown circui t or reduction in current capability. therefore, be sure to prepare sufficient ma rgin within power dissipation for usage. calculation of the maximum internal power consumption of ic (pmax) pmax=(vin-vout)iout(max.) (vin input voltage vout output voltage iout(max) maximum output current) ? measurement conditions standard rohm board layout of board for measurement ic implementation position top layer (top view) bottom layer (top view) measurement state with board im plemented (wind speed 0 m/s) board material glass epoxy resin (double-side board) board size 70 mm x 70 mm x 1.6 mm wiring rate top layer metal (gnd) wiring rate: approx. 0% bottom layer metal (gnd) wiring rate: approx. 50% through hole diameter 0.5mm x 6 holes power dissipation 0.54w thermal resistance ja=185.2c/w * please design the margin so that pmax becomes is than pd (pmax ? pd) within the usage temperature range figure 83. ssop5 power dissipation heat reduction characteristics (reference) 0 0.1 0.2 0.3 0.4 0.5 0.6 0 25 50 75 100 125 ta [ ] pd [w] 0.54w 85 standard rohm board downloaded from: http:///
tsz02201-0rbr0a300110-1-2 22/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet operation notes 1.) absolute maximum ratings use of the ic in excess of absolute maximum ratings (such as the input voltage or operating temperature range) may result in damage to the ic. assumptions should not be made regarding the state of the ic (e.g., short mode or open mode) when such damage is suffered. if operational values are expected to exceed the maximum ratings for the device, consider adding protective circuitry (such as fuses) to eliminate the risk of damaging the ic. 2.) gnd potential the potential of the gnd pin must be the minimum potential in the system in all operating conditions. never connect a potential lower than gnd to any pin, even if only transiently. 3.) thermal design use a thermal design that allows for a sufficient margin fo r that package power dissipation rating (pd) under actual operating conditions. 4.) inter-pin shorts and mounting errors use caution when orienting and posit ioning the ic for mounting on printed circuit boards. improper mounting or shorts between pins may result in damage to the ic. 5.) common impedance wiring traces should be as short and wide as possible to minimize common impedance. bypass capacitors should be use to keep ripple to a minimum. 6.) voltage of stby pin to enable standby mode for all channels, set the stby pin to 0.3 v or less, and for normal operation, to 1.2 v or more. setting stby to a voltage between 0.3 and 1.2 v may cause malfunction and should be avoi ded. keep transition time between high and low (or vice versa) to a minimum. additionally, if stby is shorted to vin, the ic will switch to standby mode and disable the output discharge circuit, causing a temporary voltage to remain on the output pin. if the ic is switched on again while this voltage is present, overshoot may occur on the output. therefore, in applications where t hese pins are shorted, the output should always be completely discharged before turning the ic on. 7.) over-current protection circuit (ocp) this ic features an integrated over-cu rrent and short-protection circuitry on the output to prevent des truction of the ic when the output is shorted. the ocp circuitry is designed only to protect the ic from irregul ar conditions (such as motor output shorts) and is not designed to be us ed as an active security device for t he application. ther efore, applications should not be designed under the assumption that this circuitry will engage. 8.) thermal shutdown circuit (tsd) this ic also features a thermal shutdown circuit that is designed to turn the output off when the junction temperature of the ic exceeds about 150 . this feature is intended to protect the ic onl y in the event of therma l overload and is not designed to guarantee operation or act as an active security device for the application. ther efore, applications should not be designed under the assumption that this circuitry will engage. 9.) input/output capacitor capacitors must be connected between the input/output pins and gnd for stable operation, and should be physically mounted as close to the ic pins as possible. the input capa citor helps to counteract increases in power supply impedance, and increases stability in applications with long or winding power supply traces. the output capacitance value is directly related to the overall stability and transient response of the regulator, and should be set to the largest possible value for the application to increase these characteri stics. during design, keep in mind that in general, ceramic capacitors have a wide range of tolerances, temperature coefficients and dc bias char acteristics, and that their capacitance values tend to decrease over time. confirm thes e details before choosing appropriate capacitors for your application.(please refer the technical note, regarding ceramic capacitor of recommendation) 10.) about the equivalent series resistance (esr) of a ceramic capacitor capacitors generally have esr (equivalent series resistance) and it operates stably in the esr-iout area shown on the right. since ceramic capacitors, tantalum capacitors, electrolytic capacitors, etc. generally have different esr, please check the esr of the capacitor to be used and use it within the stability area range shown in the right graph for evaluation of the actual application. figure 84. stable region (example) cout=1.0uf cin=1.0uf temp=25 [] [] stable unstable downloaded from: http:///
tsz02201-0rbr0a300110-1-2 23/23 29.jan.2015 rev.005 ? 2013 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 www.rohm.com buxxuc3wg ` datasheet revision history date revision changes 27.jun.2013 001 new release 02.jul.2013 002 absolute maximum ratings of power supply voltage is changed. adding reference data. 16.apr.2014 003 adding reference data. 23.jan.2015 004 line up is changed. 29.jan.2015 005 reference data is changed. downloaded from: http:///
datasheet d a t a s h e e t notice-ge rev.004 ? 2013 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohms products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. if the flow sol dering method is preferred on a surface-mount products, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice-ge rev.004 ? 2013 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 201 5 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///

▲Up To Search▲

Price & Availability of BU33UC3WG-TR

	To Download BU33UC3WG-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .